Electronics

B

Transistors

Transistors are made from semiconductors. These are materials, such as silicon or germanium, that are “doped” (have minute amounts of foreign elements added) so that either an abundance or a lack of free electrons exists. In the former case, the semiconductor is called n-type, and in the latter case, p-type. By combining n-type and p-type materials, a diode can be produced. When this diode is connected to a battery so that the p-type material is positive and the n-type negative, electrons are repelled from the negative battery terminal and pass unimpeded to the p-region, which lacks electrons. With battery reversed, the electrons arriving in the p-material can pass only with difficulty to the n-material, which is already filled with free electrons, and the current is almost zero.

The bipolar transistor was invented in 1948 as a replacement for the triode vacuum tube. It consists of three layers of doped material, forming two p-n (bipolar) junctions with configurations of p-n-p or n-p-n. One junction is connected to a battery so as to allow current flow (forward bias), and the other junction has a battery connected in the opposite direction (reverse bias). If the current in the forward-biased junction is varied by the addition of a signal, the current in the reverse-biased junction of the transistor will vary accordingly. The principle can be used to construct amplifiers in which a small signal applied to the forward-biased junction causes a large change in current in the reverse-biased junction.

Another type of transistor is the field-effect transistor (FET). Such a transistor operates on the principle of repulsion or attraction of charges due to a superimposed electric field. Amplification of current is accomplished in a manner similar to the grid control of a vacuum tube. Field-effect transistors operate more efficiently than bipolar types, because a large signal can be controlled by a very small amount of energy.

C

Integrated Circuits

Most integrated circuits are small pieces, or “chips,” of silicon, perhaps 2 to 4 sq mm (0.08 to 0.15 sq in) long, in which transistors are fabricated. Photolithography enables the designer to create tens of thousands of transistors on a single chip by proper placement of the many n-type and p-type regions. These are interconnected with very small conducting paths during fabrication to produce complex special-purpose circuits. Such integrated circuits are called monolithic because they are fabricated on a single crystal of silicon. Chips require much less space and power and are cheaper to manufacture than an equivalent circuit built by employing individual transistors.

---

---

D

Resistors

If a battery is connected across a conducting material, a certain amount of current will flow through the material (see Resistance). This current is dependent on the voltage of the battery, on the dimensions of the sample, and on the conductivity of the material itself. Resistors with known resistance are used for current control in electronic circuits. The resistors are made from carbon mixtures, metal films, or resistance wire and have two connecting wires attached. Variable resistors, with an adjustable sliding contact arm, are often used to control volume on radios and television sets.

E

Capacitors

Capacitors consist of two metal plates that are separated by an insulating material (see Capacitor). If a battery is connected to both plates, an electric charge will flow for a short time and accumulate on each plate. If the battery is disconnected, the capacitor retains the charge and the voltage associated with it. Rapidly changing voltages, such as caused by an audio or radio signal, produce larger current flows to and from the plates; the capacitor then functions as a conductor for the changing current. This effect can be used, for example, to separate an audio or radio signal from a direct current in order to connect the output of one amplifier stage to the input of the next amplifier stage.

F

Inductors

Inductors consist of a conducting wire wound into the form of a coil. When a current passes through the coil, a magnetic field is set up around it that tends to oppose rapid changes in current intensity (see Induction). As a capacitor, an inductor can be used to distinguish between rapidly and slowly changing signals. When an inductor is used in conjunction with a capacitor, the voltage in the inductor reaches a maximal value for a specific frequency. This principle is used in a radio receiver, where a specific frequency is selected by a variable capacitor.

	More from Encarta
	•  Presidential Myths Quiz •  Coffee break: Recharge your brain