Television

B

Pickup Device

The pickup device takes light from a scene and translates it into electronic signals. The first pickup devices used in cameras were camera tubes. The first camera tube used in television was the iconoscope. Invented in the 1920s, it needed a great deal of light to produce a signal, so it was impractical to use in a low-light setting, such as an outdoor evening scene. The image-orthicon tube and the vidicon tube were invented in the 1940s and were a vast improvement on the iconoscope. They needed only about as much light to record a scene as human eyes need to see. Instead of camera tubes, most modern cameras now use light-sensitive integrated circuits (tiny, electronic devices) called charge-coupled devices (CCDs).

When recording television images, the pickup device replaces the function of film used in making movies. In a camera tube pickup device, the front of the tube contains a layer of photosensitive material called a target. In the image-orthicon tube, the target material is photoemissive—that is, it emits electrons when it is struck by light. In the vidicon camera tube, the target material is photoconductive—that is, it conducts electricity when it is struck by light. In both cases, the lens of a camera focuses light from a scene onto the front of the camera tube, and this light causes changes in the target material. The light image is transformed into an electronic image, which can then be read from the back of the target by a beam of electrons (tiny, negatively charged particles).

The beam of electrons is produced by an electron gun at the back of the camera tube. The beam is controlled by a system of electromagnets that make the beam systematically scan the target material. Whenever the electron beam hits the bright parts of the electronic image on the target material, the tube emits a high voltage, and when the beam hits a dark part of the image, the tube emits a low voltage. This varying voltage is the electronic television signal.

A charge-coupled device (CCD) can be much smaller than a camera tube and is much more durable. As a result, cameras with CCDs are more compact and portable than those using a camera tube. The image they create is less vulnerable to distortion and is therefore clearer. In a CCD, the light from a scene strikes an array of photodiodes arranged on a silicon chip. Photodiodes are devices that conduct electricity when they are struck by light; they send this electricity to tiny capacitors. The capacitors store the electrical charge, with the amount of charge stored depending on the strength of the light that struck the photodiode. The CCD converts the incoming light from the scene into an electrical signal by releasing the charges from the photodiodes in an order that follows the scanning pattern that the receiver will follow in re-creating the image.

---

---

C

Encoder

In color television, the signals from the three camera tubes or charge-coupled devices are first amplified, then sent to the encoder before leaving the camera. The encoder combines the three signals into a single electronic signal that contains the brightness information of the colors (luminance). It then adds another signal that contains the code used to combine the colors (color burst), and the synchronization information used to direct the television receiver to follow the same scanning pattern as the camera. The color television receiver uses the color burst part of the signal to separate the three colors again.

IV

Scanning

Television cameras and television receivers use a procedure called scanning to record visual images and re-create them on a television screen. The television camera records an image, such as a scene in a television show, by breaking it up into a series of lines and scanning over each line with the beam or beams of electrons contained in the camera tube. The pattern is created in a CCD camera by the array of photodiodes. One scan of an image produces one static picture, like a single frame in a film. The camera must scan a scene many times per second to record a continuous image. In the television receiver, another electron beam—or set of electron beams, in the case of color television—uses the signals recorded by the camera to reproduce the original image on the receiver's screen. Just like the beam or beams in the camera, the electron beam in the receiver must scan the screen many times per second to reproduce a continuous image.

In order for television to work, television images must be scanned and recorded in the same manner as television receivers reproduce them. In the United States, broadcasters and television manufacturers have agreed on a standard of breaking images down into 525 horizontal lines, and scanning images 30 times per second. In Europe, most of Asia, and Australia, images are broken down into 625 lines, and they are scanned 25 times per second. Special equipment can be used to make television images that have been recorded in one standard fit a television system that uses a different standard. Telecine equipment (from the words television and cinema) is used to convert film and slide images to television signals. The images from film projectors or slides are directed by a system of mirrors toward the telecine camera, which records the images as video signals.

The scanning method that is most commonly used for analog television is called interlaced scanning. It produces a clear picture that does not fade. When an image is scanned line by line from top to bottom, the top of the image on the screen will begin to fade by the time the electron beam reaches the bottom of the screen. With interlaced scanning, odd-numbered lines are scanned first, and the remaining even-numbered lines are scanned next. A full image is still produced 30 times a second, but the electron beam travels from the top of the screen to the bottom of the screen twice for every time a full image is produced.

Digital television uses progressive scan, the same as most computer monitors do. The image is produced 60 times a second, with odd and even fields scanned every 0.6 seconds. The higher scan rate can produce a better picture than analog.

V

Transmission of Television Signals

The audio and video signals of a television program are broadcast through the air by a transmitter. The transmitter superimposes the information in the camera's electronic signals onto carrier waves. The transmitter amplifies the carrier waves, making them much stronger, and sends them to a transmitting antenna. This transmitting antenna radiates the carrier waves in all directions, and the waves travel through the air to antennas connected to television sets or relay stations.

A

The Transmitter

The transmitter superimposes the information from the electronic television signal onto carrier waves by modulating (varying) either the wave's amplitude, which corresponds to the wave's strength, or the wave's frequency, which corresponds to the number of times the wave oscillates each second (see Radio: Modulation). The amplitude of one carrier wave is modulated to carry the video signal (amplitude modulation, or AM) and the frequency of another wave is modulated to carry the audio signal (frequency modulation, or FM). These waves are combined to produce a carrier wave that contains both the video and audio information. The transmitter first generates and modulates the wave at a low power of several watts. After modulation, the transmitter amplifies the carrier signal to the desired power level, sometimes many kilowatts (1 kilowatt equals 1,000 watts), depending on how far the signal needs to travel, and then sends the carrier wave to the transmitting antenna.

The frequency of carrier waves is measured in hertz (Hz), which is equal to the number of wave peaks that pass by a point every second. The frequency of the modulated carrier wave varies, covering a range, or band, of about 4 million hertz, or 4 megahertz (4 MHz). This band is much wider than the band needed for radio broadcasting, which is about 10,000 Hz, or 10 kilohertz (10 kHz). Television stations that broadcast in the same area send out carrier waves on different bands of frequencies, each called a channel, so that the signals from different stations do not mix. To accommodate all the channels, which are spaced at least 6 MHz apart, television carrier frequencies are very high. Six MHz does not represent a significant chunk of bandwidth if the television stations broadcast between 50 and 800 MHz.

In the United States and Canada, there are two ranges of frequency bands that cover 67 different channels. The first range is called very high frequency (VHF), and it includes frequencies from 54 to 72 MHz, from 76 to 88 MHz, and from 174 to 216 MHz. These frequencies correspond to channels 2 through 13 on a television set. The second range, ultrahigh frequency (UHF), includes frequencies from 407 MHz to 806 MHz, and it corresponds to channels 14 through 69. However, channel 37 is used for radio astronomy and medical telemetry equipment, not for television broadcasting (see Radio and Television Broadcasting). When the transition to all-digital television broadcasting is complete, channels 52 through 69 will no longer be used for television signals. These frequencies may become available for other uses such as wireless communication.

The high-frequency waves radiated by transmitting antennas can travel only in a straight line, and may be blocked by obstacles in between the transmitting and receiving antennas. For this reason, transmitting antennas must be placed on tall buildings or towers. In practice, these transmitters have a range of about 120 km (75 mi). In addition to being blocked, some television signals may reflect off buildings or hills and reach a receiving antenna a little later than the signals that travel directly to the antenna. The result is a ghost, or second image, that appears on the television screen. Digital transmission, however, eliminates ghosts and snow since the picture that results is recreated from a digital code, not from analog waves. Television signals may also be sent clearly from almost any point on Earth to any other—and from spacecraft to Earth—by means of cables, microwave relay stations, and communications satellites.

	More from Encarta
	•  Presidential Myths Quiz •  Coffee break: Recharge your brain